BCE FM Tacho

Manufacturer:

BCE FM-500 Tacho is a new generation fleet management device, equipped with a rich pack of interfaces, full range of CAN-bus data, remote tachograph data download and a wide variety of available accessories makes this device a powerful tool for satisfying the needs of the most demanding customer in fleet management field.

BCE FM Tacho description

Location and tracking

  • GPS/GLONASS
  • Continuous tracking mode
  • LBS

Mobile networks

Standard quad-band GSM, no 3G support.

Power supply

Internal 700 mAh battery. Acceptable voltage 8 – 36 V

Device features protection from impulses up to 120 V

Consumption at 12 V: active – < 50 mA, sleep – < 8mA

 

Inputs and outputs

1-wire interface
4x digital inputs (frequency, impulse counter, ON/OFF modes)
2x analogue inputs
3x digital outputs

Digital and analog inputs of the device together with 1-Wire interface may be used to connect different external sensors/devices. Outputs of the device may be used to control external equipment remotely. Flexible configuration allows users/dealers to adjust the device to meet their specific requirements.

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Axle loadFeature already supported
Feature already supported in
Navixy hidden
Navixy server port47727
Feature already supported in
Navixy model code hiddenbcefm_tacho
Feature already supported in
Powered by Navixy
Feature already supported in
Housing
Weight62 g (2.19 oz.)
Feature already supported in
Size26x80x55 mm (1.02x3.15x2.17 in)
Feature already supported in
Interfaces
1-Wire interface
Feature already supported in
RS232 interface
Feature already supported in
RS485 interface
Feature already supported in
Number of outputs3
Feature already supported in
Number of inputs (all types)6
Feature already supported in
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature already supported
Feature already supported in
Impulse inputsFeature can be supported upon request
Feature can be supported upon request
Frequency inputsFeature can be supported upon request
Feature can be supported upon request
Hardware extras
Fuel level sensor readingFeature already supported
Feature already supported in
Driver ID readingFeature already supported
Feature already supported in
External temperature sensor readingFeature already supported
Feature already supported in
Tracking features
Tracking modesContinuous
Feature already supported in
OdometerFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
CAN/OBDII reading
CAN/OBDII reader typeFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in

Tracking software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47727

Automatic activation

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode through the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set the local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending the following command to the device:

W{apn},{apn_user},{apn_pass},0.0.0.0,217.23.132.215,47727

The <APN> parameters depend on your GSM carrier and should be sent without brackets.

Reviews

There are no reviews yet.

Be the first to review “BCE FM Tacho”

Related Articles

2018, TelematicsTalks powered by Navixy | About