CalAmp TTU-2830

Manufacturer:

CalAmp TTU-2830 is a weatherproof vehicle tracker designed for long deployments. Built-in battery allows this tracker to save data during disconnect from the main power supply.

CalAmp TTU-2830 description

CalAmp TTU-2830 is a weatherproof vehicle tracker designed for long deployments. Built-in battery allows this tracker to save data during disconnect from the main power supply.

Location and tracking

  • GPS
  • Continous tracking mode
  • LBS

Mobile networks

  • GSM 850/900/1800/1900
  • HSPA/UMTS 800/850/900/1700/1900/2100
  • 2G

Inputs and outputs

  • 3 digital inputs (1 fixed, 2 programmable)
  • 1 analog input
  • 3 digital outputs
  • 1-Wire interface

Power supply

  • Built-in 5.3 mAh battery

Other features

  • IP-66 protection
  • Operating temperature -20° to +70° C

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47710
General information
PurposeVehicle
InstallationProfessional
Housing
Weight340 g (11.99 oz.)
Size110x54x40 mm (4.33x2.13x1.57 in)
Waterproof classIP66
GNSS Location
Internal antenna (GNSS)
GPS
Assisted GPS
Connectivity
Cellular network typeGSM 850/900/1800/1900
Internal antenna (Connection)
Cellular network generation2G
Interfaces
1-Wire interface
Number of outputs3
Number of inputs (all types)4
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature already supported
Feature already supported in
OutputsFeature already supported
Feature already supported in
Hardware features
Built-in battery
Feature already supported in
Tracking features
Tracking modesContinuous
Feature already supported in
Location by Cell IDFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
Network operator IDFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47710

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

!RP,2306,0,<apn>
!RP,2314,0,<apnUser>
!RP,2315,0,<apnPass>
!RP,1024,35,255,1
!RP,769,0,47710
!RP,2319,0,<server_ip>
!RP,768,0,<server_ip>
!RP,1024,25,255,2
!R3,70,0
!R3,1,123

The <APN> parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “CalAmp TTU-2830”

2018, TelematicsTalks powered by Navixy | About