FORT-112 3G

Manufacturer:

FORT-112 is a vehicle GPS tracker used for tracking, security and fleet management services. The device support 3G networks and can make an emergency call in “ERA-GLONASS” system.

FORT-112 3G description

FORT-112 is a vehicle GPS tracker used for tracking, security and fleet management services. The device support 3G networks and can make an emergency call in “ERA-GLONASS” system.

The emergency call consists of transmitting a minimally required data by voice channel on number 112, using build-in InBand modem, and after this establish a voice connection to emergency operator.

Location and tracking

  • GPS and GLONASS
  • Continuous and interval tracking modes
  • LBS support

Mobile networks

  • UMTS-2000, 900/2100 MHz
  • 3G support

Power supply

  • Build-in battery 1800 mAh
  • Input voltage 8-40V

Inputs and outputs

  • 2 analog-digital inputs
  • 4 digital inputs with impulse counting feature
  • 1 ignition input
  • RS-232 and RS-485 ports
  • 1-Wire
  • CAN support

Other features

  • Ability to send data to two different servers
  • Can work in EGTS protocol
  • Configuration over SMS, GPRS, USB

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47730
General information
PurposeVehicle
InstallationProfessional
Housing
Weight400 g (14.11 oz.)
Size104x122x33 mm (4.09x4.8x1.3 in)
GNSS Location
Internal antenna (GNSS)
GPS
GLONASS
Connectivity
Cellular network typeGSM 900/2100, UMTS-2000
Internal antenna (Connection)
Cellular network generation3G
Interfaces
1-Wire interface
RS232 interface
Number of RS232 interfaces1
RS485 interface
Number of outputs2
Number of inputs (all types)7
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
Analog inputsFeature already supported
Feature already supported in
Hardware extras
Fuel level sensor readingFeature already supported
Feature already supported in
Voice listeningFeature can be supported upon request
Feature can be supported upon request
Driver ID readingFeature already supported
Feature already supported in
External temperature sensor readingFeature already supported
Feature already supported in
Tracking features
Tracking modesContinuous, Interval
Feature already supported in
Location by Cell IDFeature already supported
Feature already supported in
OdometerFeature already supported
Feature already supported in
ECO drivingFeature can be supported upon request
Feature can be supported upon request
Events monitoring
Battery lowFeature already supported
Feature already supported in
Self monitoring
Network signal levelFeature already supported
Feature already supported in
GNSS signal levelFeature already supported
Feature already supported in
External power source voltageFeature already supported
Feature already supported in
Internal battery levelFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Remote outputs control
Feature already supported in
Forced GNSS location update over SMSFeature can be supported upon request
Feature can be supported upon request

Server software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47730

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending following commands to the device:

APN={apn}:{apn_user}:{apn_pass}#1234
SERVER=217.23.132.215:47730#1234
RESET#1234

The {apn} parameters depend on your GSM carrier.

Reviews

There are no reviews yet.

Be the first to review “FORT-112 3G”

2018, TelematicsTalks powered by Navixy | About