Model: MyRope M588

Manufacturer:

MyRope M588 is a multifunctional cost-effective solution for real-time tracking & fleet management. It houses a number of advanced features such as: built-in antenna, voice monitoring, sos alarm and water resistance.

MyRope M588 description

MyRope M588 is a multifunctional cost-effective solution for real-time tracking & fleet management. It houses a number of advanced features such as: built-in antenna, voice monitoring, sos alarm and water resistance.

Features

  • Built-in antenna;
  • Low power alarm;
  • Idling alarm;
  • Water resistance.

Package content

  • GPS unit;
  • Relay;
  • I/O Cable;
  • Mic;
  • Packaging Box.

Location and tracking

M588 tracking is based on GPS signals only. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking). Supports real time tracking at intervals.

Mobile networks

With Quad-band GSM 2G module M588 can be operated all over the world.

Power supply

External power supply might be 8-50V, which makes it possible to install M588 both on cars and vans. M588 also features a built-in rechargeable backup battery. When fully charged it ensures about 2 hours of device operation (in normal conditions).

Remote management

M588 tracker can be fully controlled over GPRS. There is also a wide list of SMS commands in a human-friendly format, on which device always replies back. It supports remote APN settings configuration by SMS.

LED indication

M588 has LED indication for Power, GPS and GSM status.

Specifications and Features

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47666
General information
PurposeVehicle
InstallationProfessional
Housing
Weight50 g (1.76 oz.)
Size89x37x12 mm (3.5x1.46x0.47 in)
GNSS Location
Internal antenna (GNSS)
GPS
Connectivity
Cellular network typeGSM Quad Band
Internal antenna (Connection)
Cellular network generation2G
Interfaces
Number of outputs1
Number of inputs (all types)1
ACC/Ignition inputFeature already supported
Feature already supported in
Discrete inputsFeature already supported
Feature already supported in
OutputsFeature already supported
Feature already supported in
Hardware features
Emergency buttonFeature already supported
Feature already supported in
Hardware extras
Emergency buttonFeature already supported
Feature already supported in
Tracking features
Tracking modesContinuous
Feature already supported in
OdometerFeature already supported
Feature already supported in
Events monitoring
Battery lowFeature already supported
Feature already supported in
External power cut offFeature already supported
Feature already supported in
Self monitoring
External power source voltageFeature already supported
Feature already supported in
Remote management
Server connection setup over SMSFeature already supported
Feature already supported in
Remote device configurationYes (over GPRS)Feature already supported
Feature already supported in
Remote outputs controlYes (over GPRS)Feature already supported
Feature already supported in
Forced GNSS location update over SMSFeature can be supported upon request
Feature can be supported upon request

Tracking software

Navixy

Server Integration
Server IP Address217.23.132.215
Server port47666

Automatic activation

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode through the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set the local Time zone, it must be UTC+0h (as by default)

Manual activation

In case automatic activation failed, you can try to register the device manually by sending the following command to the device:

<ss,apn_name,apn_user,apn_pwd,217.23.132.215,47666,system_number,device_password>

The <APN> parameters depend on your GSM carrier and should be sent without brackets.

Reviews

There are no reviews yet.

Be the first to review “MyRope M588”

2019, TelematicsTalks powered by Navixy | About